Blog

What Is Fiber Optic Cable? Explained

In this guide
  1. How Do Fiber Optic Cables Work?
  2. Single Mode vs Multimode Fiber Cables
  3. Tight-buffered Breakout/Distribution Cable
  4. Why Use Fiber Cables Instead of Copper Cables?
  5. Fiber Optic Connector Types
  6. Fiber Optic Cables Applications
  7. How to Clean Fiber Optic Cable?

Fiber optic cables are made up of one or more transparent fibers surrounded by protective covers and strength members. Signals such as light can travel through fiber optic cables without interference.

How Do Fiber Optic Cables Work?

A fiber optic cable is made of glass strands, each slightly thicker than a human hair. Each strand has a core in the middle that lets light pass through. The core is surrounded by a second layer of glass called cladding, which bounces light inward to prevent signal loss and lets the light follow the cable's bends. This is called total internal reflection: light travels through the core (the hallway) by constantly bouncing off the cladding (the mirror-lined walls).

Coatings are the layers of plastic that surround the fiber. They act as a buffer, absorbing shock and adding an extra layer of protection.

Single Mode vs Multimode Fiber Cables

Multimode and single mode fiber transmit light in different ways. Because multimode fiber has a larger core, some light beams travel straight through while others bounce off the cladding. Single mode fiber has a core diameter up to five times smaller than multimode fiber, and it allows only one mode of light to pass through the core.

Multimode fiber comes in two core diameters: 50 µm and 62.5 µm. Because of its relatively wide core, it can carry multiple data streams at 850 nm or 1300 nm wavelengths at the same time. Due to high dispersion and attenuation rates, multimode fiber is typically used to carry a high volume of data over relatively short distances. It uses a light-emitting diode (LED) or a Vertical Cavity Surface Emitting Laser (VCSEL) as its light source.

Single mode fiber has much less internal reflection as light passes through it, which reduces attenuation and enables much faster data transfer over long distances. Multimode fiber cabling, on the other hand, greatly increases the amount of reflection. This results in higher dispersion and attenuation rates and, as a result, increased bandwidth delivery over shorter distances.

Colors

The colors of the two types of fiber cable make them easy to tell apart when selecting cables. Most single mode cables are yellow, while multimode cables are usually orange or aqua.

Diameter

The core of every fiber cable carries light to transmit data. The main difference between single mode vs multimode fiber cables is the size of their cores. Single mode fiber optic cables have a much smaller core diameter than multimode cables. The 9-micron standard used in broadcasting and production reduces attenuation and allows signals to travel further. The multimode core diameters used in A/V are 50 or 62.5 microns, which allow more data to pass through the fibers at the same time.

Transmission Distance

Single mode fibers are better suited to long-distance applications because of their high bandwidth. Multimode fibers have a larger core, so modal dispersion (the overlapping of pulses) increases over longer distances. This makes multimode fiber the better choice for shorter-distance applications.

Tight-buffered Breakout/Distribution Cable

Breakout Cable

Breakout Cable Structure

A breakout cable is also called a fan-out cable. It is made up of two or more simplex cables bundled around a central strength member. Each fiber has its own jacket, and they are all packaged together inside the same outer jacket. As a result, when running through building walls, breakout cables can be separated into individual simplex cables for separate use. Breakout cables are typically designed with a tight buffer and fiber counts ranging from 2 to 24 fibers.

Breakout Cable System Layout

For direct connectivity, a tight-buffered breakout cable is the best option. Each fiber has its own aramid strength member for connector tie-off, so in most situations the sub-cables can be connected directly to equipment without fear of damaging the fiber, the connector or the fiber end face.

Distribution Cable

Distribution Cable Structure

A distribution cable is smaller and lighter than a breakout cable. Its fiber count can be higher, up to 144 fibers. Many of these fibers may not be used right away and can be saved for future use. Although the distribution cable has a more compact design, the tight-buffered fibers inside are protected only by a single outer jacket. This makes distribution fiber optic cable easier to handle and strip for field termination.

Distribution Cable System Layout

Tight-buffered distribution cables are simple to route, and their 900 µm tight-buffered fiber allows fast and reliable field terminations. The terminated fibers are placed in a patch panel, and jumper cables connect the patch panel to the equipment.

Why Use Fiber Cables Instead of Copper Cables?

Fast data transmission, thinner and lighter cables, and extended signal range are just a few of the advantages that make fiber optic cable an excellent choice for corporate data networking and telecommunications.

EMI (Electromagnetic Interference)

Copper wires generate an electromagnetic field that can cause signaling errors in other cables. Fiber cables, on the other hand, do not generate electromagnetic interference (EMI), and they are not affected by it either. You can put them right next to industrial equipment without worrying about it.

High-Speed Data Transmission

Fiber optic cables use light pulses and are made of tiny strands of glass about the width of a human hair. Comparing fiber optic and copper transmission means comparing the speed of photons with the speed of electrons. Photons travel at the speed of light, whereas electrons in copper travel at less than 1% of the speed of light. Copper currently has a top speed of 40 Gbps, whereas OM5 fiber has a top speed of 100 Gbps. What's more, unlike cable broadband and DSL, fiber optic connections do not degrade over distance, which allows consistent, high data transfer speeds.

High Bandwidth Level

The main advantage of optical fiber communication over electrical cable transmission is its high bandwidth (nearly 10 Gbps) over long distances, thanks to extremely low loss at specific wavelengths (for example 1.3 µm and 1.55 µm).

Fiber also reduces latency, which means faster downloads and uploads and faster access to resources. Because of its low loss, fiber can also carry data over longer distances without delays or interruptions.

More Secure

A broken or damaged optical fiber can be detected very quickly with a variety of monitoring techniques, such as monitoring the actual power transmission or a pilot signal. Without such monitoring, a damaged, old or worn copper cable carrying a current can short out completely or even cause a fire.

Light Weight, Water-Proof, and Extended Lifespan

Fiber cables are roughly one quarter the diameter and one tenth the weight of copper cables. This makes them easier to install and allows better airflow in rack enclosures. Furthermore, unlike copper cables, fiber optic cable is not affected by temperature changes, bad weather or moisture. A fiber optic cable should last at least ten years, and they often last much longer.

Fiber Optic Connector Types

SC (Subscriber Connector)

SC is a push-pull connector that uses a ceramic ferrule to deliver highly accurate alignment in a fiber optic link. SC connectors have a dependable snap-in locking mechanism that latches with a simple push-pull motion. They are a low-cost, long-lasting option that can withstand 1,000 mating cycles. This connector can be used in both simplex and duplex mode. The new SC connectors simplify installation even more, maximize yield, and provide guaranteed insertion and return loss performance comparable to factory-terminated connectors.

LC (Lucent Connector/Little Connector)

The LC is also a push-pull connector, but it uses a latch instead of the SC locking tab and has a smaller ferrule, which makes it a small form factor connector. With half the footprint of the SC connector, it is extremely popular in datacoms and other high-density patch applications. Its small size and latch make it ideal for densely populated racks and panels.

FC (Ferrule Connector/Fixed Connector)

For durability, an FC connector uses an all-zirconia ceramic ferrule. For repeatability and interoperability, it has a high-performance threaded mounting system and a keyed body. FC connectors are mostly used with single mode fibers in telephone, instrument and high-speed communication links. The design is similar to that of an ST connector, but the threaded connection makes it more suitable for high-vibration environments.

ST (Straight Tip)

AT&T developed the ST connector shortly after the FC arrived. ST connectors are commonly used in fiber optic networking and work for both short-distance and long-distance applications. Known as "stick and twist", it is an older technology, but it is still widely used on data networks and has a large installed base.

Fiber Optic Cables Applications

There are many applications for fiber optic cables. Telecommunication companies use them to transmit telephone signals, internet communication signals and cable television signals.

Ethernet

Optical fibers are used to connect servers and users in many network setups, and they improve the accuracy and speed of data transfer. Compared with traditional copper wiring, fiber optic cables are lighter, less bulky and more flexible, and they can carry large amounts of data at very high speeds. As a result, fiber optic cables are increasingly used for internet connections.

Auto Industry

Mercedes-Benz successfully introduced plastic optical fiber (POF) in automobile networking systems in 1998. Following this, the Media Oriented Systems Transport (MOST) standard was developed: a stable and robust network protocol for in-car multimedia, entertainment and information.

Fiber optic cables are used to light both the exterior and interior of cars, and they play an important role in lighting and safety. They can also transmit signals between different parts of a vehicle at high speed.

Television

Fiber delivery technologies offer many advantages to both TV companies and their customers. Because fiber has more bandwidth and higher speeds, it is ideal for transmitting signals to HD televisions. In addition, fiber optic cables are less expensive than copper wires.

Medical

Endoscopy (a non-intrusive surgical method) relies heavily on optical fiber. In this procedure, a small, bright light illuminates the area inside the body, which reduces the number and size of incisions. Biomedical research and microscopy also make use of fiber optics.

Cloud Data Storage

With the growing popularity of cloud computing, there is greater demand for data capacity and higher bandwidth. Cloud services are internet-based, so their performance and productivity depend on your internet connection. Many businesses are switching to fiber optic connectivity to make the most of the cloud. Cloud computing would be ineffective without enough bandwidth.

How to Clean Fiber Optic Cable?

It is critical to clean fiber optics before installation. A new cable is not guaranteed to be clean, and the installation process can introduce dust and other contaminants. Always clean the end of a fiber optic cable before inserting it into a connector.

There are two types of fiber optic connector applications that need cleaning: free connectors on a fiber optic patch cable or pigtail, and connectors plugged into patch panels or other hardware and equipment.

There are several methods for cleaning fiber optic cables. Here is one you can try:

  1. To dislodge any larger, loose particles, blow the surface of the fiber with CDA (canned dry air).
  2. Place a few drops of a suitable cleaning solution, such as spectroscopic-grade isopropyl alcohol or methanol, in the center of a lens tissue.
  3. Grip the fiber gently by the cable or connector. Place the wet part of the tissue on the optical surface and slowly move it across the fiber.
  4. Examine the fiber surface in bright light with a magnifier, video inspection tool or optical loupe. If any contaminants or streaks are visible, repeat the process with a new lens tissue.
  5. When you finish cleaning, put a protective cover on the end of the cable or reinsert the fiber to prevent recontamination.

To avoid damage, take great care throughout the cleaning process and follow these guidelines:

  • Do not tip the CDA can while blowing. This can release liquid, which will contaminate the fiber surface.
  • Dry lens paper is extremely abrasive and should never be used.
  • Never use acetone to clean fiber optic surfaces.
  • Dipping the lens tissue into the methanol or isopropyl alcohol can contaminate the liquid. Drip the cleaning solution onto the tissue instead.

Written by

addison

Published on TheTechRim in Blog.